Hi All,
Currently i have a 2-Mbps BSNL broadband connection which is terminated to our Linux Server (Fedora) which acts as the Internet gateway to our LAN users from the DSL Modem using PPPoE.
Now, i want to replace this with a new 2-Mbps AIRTEL broadband connection. My queries:
1. Should i run the ADSL-SETUP again for the new connection.
2. If i add another NIC(for the new connection) and run the ADSL-SETUP, will this affect the existing connection.
3. Is there a way such that, i can configure this new Airtel connection without disturbing the existing BSNL connection and just swap the DSL modem.
Thanks & Regards, George John.
On Wednesday 06 May 2009, george@annamsoft.com wrote:
Currently i have a 2-Mbps BSNL broadband connection which is terminated to our Linux Server (Fedora) which acts as the Internet gateway to our LAN users from the DSL Modem using PPPoE.
Now, i want to replace this with a new 2-Mbps AIRTEL broadband connection. My queries:
- If i add another NIC(for the new connection) and run the
ADSL-SETUP, will this affect the existing connection.
- Is there a way such that, i can configure this new Airtel
connection without disturbing the existing BSNL connection and just swap the DSL modem.
Not clear: do you want to replace the existing BSNL connection or do you want to have both connections (BSNL and Airtel)?
In any case, you can run PPPoE for both (or either) on a single ethernet card. That's what I'm doing with my MTNL and Airtel connections.
Regards,
-- Raju
My objective is not to make the existing BSNL line go down at the same time want to configure for the AIRTEL line and once the AIRTEL line has been configured sucessfully, i can remove the BSNL line. Can this be done, if yes pl. tell me how.
It's great if we can run PPPoE for both on a single Ethernet.
Rgds, George John.
On Wednesday 06 May 2009, george@annamsoft.com wrote:
Currently i have a 2-Mbps BSNL broadband connection which is terminated to our Linux Server (Fedora) which acts as the Internet gateway to our LAN users from the DSL Modem using PPPoE.
Now, i want to replace this with a new 2-Mbps AIRTEL broadband connection. My queries:
- If i add another NIC(for the new connection) and run the
ADSL-SETUP, will this affect the existing connection.
- Is there a way such that, i can configure this new Airtel
connection without disturbing the existing BSNL connection and just swap the DSL modem.
Not clear: do you want to replace the existing BSNL connection or do you want to have both connections (BSNL and Airtel)?
In any case, you can run PPPoE for both (or either) on a single ethernet card. That's what I'm doing with my MTNL and Airtel connections.
Regards,
-- Raju
Raj Mathur raju@kandalaya.org http://kandalaya.org/ GPG: 78D4 FC67 367F 40E2 0DD5 0FEF C968 D0EF CC68 D17F PsyTrance & Chill: http://schizoid.in/ || It is the mind that moves -- http://mm.glug-bom.org/mailman/listinfo/linuxers
On Wednesday 06 May 2009, george@annamsoft.com wrote:
My objective is not to make the existing BSNL line go down at the same time want to configure for the AIRTEL line and once the AIRTEL line has been configured sucessfully, i can remove the BSNL line. Can this be done, if yes pl. tell me how.
Yes it can. The simplest method would be to copy your BSNL configuration in /etc/ppp/peers/ to a new file (say, Airtel) then manually edit it and change the parameters to match the Airtel connection. There may be GUI methods of doing this too, but being a command-line type of person this was what I found most convenient.
BTW, all DSL modems supplied in India tend to have the same default IP address (192.168.1.1). If you have two on the same network you will need to change the IP address of one of them.
Regards,
-- Raju
I could find a directory and a file in /etc/ppp/peers/ directory
1. Directory name is : isdn (i think it is not related to our setup)
2. File : wvdial, the contents of /etc/ppp/peers/wvdial is : noauth name wvdial usepeerdns
Here what should i change with respect to AIRTEL.
If i run the command # adsl-setup, it's prompting me for a new connection:
Please enter the device if you want to configure the present DSL config (default ppp0) or enter 'n' if you want to create a new one:
can i do this? Will it deactivate the present link?
Regards, George John.
Yes it can. The simplest method would be to copy your BSNL configuration in /etc/ppp/peers/ to a new file (say, Airtel) then manually edit it and change the parameters to match the Airtel connection. There may be GUI methods of doing this too, but being a command-line type of person this was what I found most convenient.
BTW, all DSL modems supplied in India tend to have the same default IP address (192.168.1.1). If you have two on the same network you will need to change the IP address of one of them.
Regards,
-- Raju
Raj Mathur raju@kandalaya.org http://kandalaya.org/ GPG: 78D4 FC67 367F 40E2 0DD5 0FEF C968 D0EF CC68 D17F PsyTrance & Chill: http://schizoid.in/ || It is the mind that moves -- http://mm.glug-bom.org/mailman/listinfo/linuxers
On Wed, May 6, 2009 at 10:52 AM, Raj Mathur raju@linux-delhi.org wrote:
On Wednesday 06 May 2009, george@annamsoft.com wrote:
My objective is not to make the existing BSNL line go down at the same time want to configure for the AIRTEL line and once the AIRTEL line has been configured sucessfully, i can remove the BSNL line. Can this be done, if yes pl. tell me how.
Yes it can. The simplest method would be to copy your BSNL configuration in /etc/ppp/peers/ to a new file (say, Airtel) then manually edit it and change the parameters to match the Airtel connection. There may be GUI methods of doing this too, but being a command-line type of person this was what I found most convenient.
BTW, all DSL modems supplied in India tend to have the same default IP address (192.168.1.1). If you have two on the same network you will need to change the IP address of one of them.
As for GUI, you can just use 'Auto eth0' of NetworkManager. I mean considering the modems can connect to ISP, the dhcp thing from dsl/adsl modem can be easily handled by NetworkManager. Swap the modem, connect the lan cable to computer and it'll be automatically connected to internet by NetworkManager.
cheers
Arindam
On Wed, May 6, 2009 at 9:38 PM, Arindam Ghosh makghosh@gmail.com wrote:
considering the modems can connect to ISP (by itself i mean)
--Arindam
On Wednesday 06 May 2009, Arindam Ghosh wrote:
As for GUI, you can just use 'Auto eth0' of NetworkManager. I mean considering the modems can connect to ISP, the dhcp thing from dsl/adsl modem can be easily handled by NetworkManager. Swap the modem, connect the lan cable to computer and it'll be automatically connected to internet by NetworkManager.
What you're saying works if you're routing through the modems. However I don't think that's going to work here, since the OP needs to put the modem(s) into bridge mode and run PPPoE on his Linux box to make a connection to each ISP.
Regards,
-- Raju
What is "OP"
On Wednesday 06 May 2009, Arindam Ghosh wrote:
As for GUI, you can just use 'Auto eth0' of NetworkManager. I mean considering the modems can connect to ISP, the dhcp thing from dsl/adsl modem can be easily handled by NetworkManager. Swap the modem, connect the lan cable to computer and it'll be automatically connected to internet by NetworkManager.
What you're saying works if you're routing through the modems. However I don't think that's going to work here, since the OP needs to put the modem(s) into bridge mode and run PPPoE on his Linux box to make a connection to each ISP.
Regards,
-- Raju
Raj Mathur raju@kandalaya.org http://kandalaya.org/ GPG: 78D4 FC67 367F 40E2 0DD5 0FEF C968 D0EF CC68 D17F PsyTrance & Chill: http://schizoid.in/ || It is the mind that moves -- http://mm.glug-bom.org/mailman/listinfo/linuxers
On Thursday 07 May 2009 09:55:56 george@annamsoft.com wrote:
What is "OP"
you - Original Poster. You may also google for 'top posting' while you are about it.
On Thu, May 7, 2009 at 8:41 AM, Raj Mathur raju@linux-delhi.org wrote:
On Wednesday 06 May 2009, Arindam Ghosh wrote:
As for GUI, you can just use 'Auto eth0' of NetworkManager. I mean considering the modems can connect to ISP, the dhcp thing from dsl/adsl modem can be easily handled by NetworkManager. Swap the modem, connect the lan cable to computer and it'll be automatically connected to internet by NetworkManager.
What you're saying works if you're routing through the modems. However I don't think that's going to work here, since the OP needs to put the modem(s) into bridge mode and run PPPoE on his Linux box to make a connection to each ISP.
Well, actually there will be a single connection between modem & server, and rest of the routing work is to done by server. But IMO, the CLI method that you told is much better for server, because NetworkManager may not even be running on it (need to logon to a desktop environment that costs resource :-). Also for a server, having public IP will be better.
--Arindam
Arindam Ghosh wrote:
On Thu, May 7, 2009 at 8:41 AM, Raj Mathur raju@linux-delhi.org wrote:
On Wednesday 06 May 2009, Arindam Ghosh wrote:
As for GUI, you can just use 'Auto eth0' of NetworkManager. I mean considering the modems can connect to ISP, the dhcp thing from dsl/adsl modem can be easily handled by NetworkManager. Swap the modem, connect the lan cable to computer and it'll be automatically connected to internet by NetworkManager.
What you're saying works if you're routing through the modems. However I don't think that's going to work here, since the OP needs to put the modem(s) into bridge mode and run PPPoE on his Linux box to make a connection to each ISP.
Well, actually there will be a single connection between modem & server, and rest of the routing work is to done by server. But IMO, the CLI method that you told is much better for server, because NetworkManager may not even be running on it (need to logon to a desktop environment that costs resource :-). Also for a server, having public IP will be better.
GUI network managers are a PITA. I was once a GUI lover but now I prefer CLI wherever possible.
Hi Raju,
Hi Raju,
How do i run PPPoE for 2 ISP's (Airtel & BSNL) on a single ethernet card.
Following is my requirement:
1. I want to add an additional Airtel DSL line to the existing BSNL DSL line.(the result should be both the DSL line should terminate on to our Linux(FC4) gateway machine
2. Either of the line should be a backup line and if one ISP goes down, the internet should be up through the available line.
Please suggest me as how to achieve it.
Regards, George John.
Not clear: do you want to replace the existing BSNL connection or do you want to have both connections (BSNL and Airtel)?
In any case, you can run PPPoE for both (or either) on a single ethernet card. That's what I'm doing with my MTNL and Airtel connections.
Regards,
-- Raju
Raj Mathur raju@kandalaya.org http://kandalaya.org/ GPG: 78D4 FC67 367F 40E2 0DD5 0FEF C968 D0EF CC68 D17F PsyTrance & Chill: http://schizoid.in/ || It is the mind that moves -- http://mm.glug-bom.org/mailman/listinfo/linuxers
On Thursday 07 May 2009, george@annamsoft.com wrote:
How do i run PPPoE for 2 ISP's (Airtel & BSNL) on a single ethernet card.
Following is my requirement:
- I want to add an additional Airtel DSL line to the existing BSNL
DSL line.(the result should be both the DSL line should terminate on to our Linux(FC4) gateway machine
- Either of the line should be a backup line and if one ISP goes
down, the internet should be up through the available line.
Had done a write-up about this, see if that helps: http://wiki.kandalaya.org/cgi-bin/twiki/view/Main/LoadBalancing
Regards,
-- Raju
-
Arindam Ghosh -
george＠annamsoft.com -
Kenneth Gonsalves -
Raj Mathur -
Rony